A chimney cap is a small piece of metal that does an outsized job. It keeps rain out of the flue, stops birds and raccoons from nesting in it, and catches the sparks that could land on your roof. But none of that works if the cap is not attached properly. A cap that slides off in the first big windstorm is worse than no cap at all, because it leaves you thinking the chimney is protected when it is wide open.
The tricky part is that there is no single way to attach one. The right method depends on the cap style, whether your flue sticks up above the crown or sits flush with it, and whether you have one flue or several. Pick the wrong method and you can crack a clay flue tile or split a concrete crown. This guide covers every attachment method used in 2026, the exact measurements each one needs, what each costs, and the mistakes to avoid. A cap is part of the same weather defense as the roof underlayment under your shingles, and it deserves the same care.
What a Chimney Cap Is and What It Does
A chimney cap is a metal hood that sits over the top of the flue, the clay or metal tube that carries smoke and combustion gases out of your home. Most caps have three parts: a solid lid that sheds rain, mesh sides that let smoke out while keeping animals and debris out, and a base that fastens to the flue or the crown.
A good cap does five jobs at once. It keeps rain out of the flue, where water would soak the flue liner, stain the firebox, and rust the damper. It keeps animals and nesting material out, which is a fire hazard if you light a fire with a nest in the flue. It catches embers and sparks before they can land on the roof or nearby trees. It cuts down on downdrafts, the gusts that push smoke and cold air back down into the house. And it keeps leaves and debris from blocking the flue, which can send carbon monoxide back into the living space.
The mesh sides are the part most people get wrong. That mesh is a spark arrestor, and its opening size is regulated. The International Residential Code says a spark arrestor screen must stop a sphere 1/2 inch wide and pass a sphere 3/8 inch wide, and the net free area of the screen must be at least four times the net area of the flue outlet. Most stock caps use 3/4 inch mesh, which suits most homes, but in wildfire prone areas local codes often require tighter mesh. Check your local code before you buy, because a cap with the wrong mesh can fail an inspection even if it fits perfectly.
Cap, Crown, Flue, and Spark Arrestor: Do Not Mix Them Up
Much of the confusion about chimney caps comes from mixed up terms, and the terms matter because each part takes a different attachment method.
The flue is the liner inside the chimney, usually a clay tile or a metal pipe, that carries smoke upward. The crown is the sloped concrete or mortar top of a masonry chimney. It seals the flue and the top layer of brick together and sheds water away from the chimney. The cap is the metal hood that goes over the flue. The spark arrestor is the mesh screen on the sides of the cap, and it is often sold as part of the cap rather than as a separate piece.
Why this matters: a cap that attaches to the flue uses clamps or set screws that grip the flue tile, while a cap that attaches to the crown uses masonry anchors or mortar on the concrete surface. If you buy a flue mount cap for a chimney where the flue sits flush with the crown, it has nothing to grip. If you buy a crown mount cap for a chimney with a tall protruding flue, it may not clear the flue at all. Measure both the flue and the crown before you order anything.
Tools and Materials You Need
Gather everything before you climb up, so you make one trip up and one trip down.
- Tape measure and pencil
- The chimney cap, sized to your flue or crown
- Nut driver or socket wrench, for set screws and bolts
- Power drill and impact driver
- Hammer drill with a 3/16 inch masonry bit, for crown mount caps
- Masonry anchors or screws, usually supplied with the cap
- Wire brush and scraper, for cleaning the crown and flue
- Caulk gun with elastomeric chimney sealant or high temperature sealant
- Type S mortar and a trowel, only for mortar set caps
- Extension ladder that reaches at least 3 feet above the roofline
- Work gloves, eye protection, and shoes with rubber soles
Work with a partner if you can. One person steadies the ladder and hands up tools while the other works on the chimney. Never work on a roof in wind, rain, or wet conditions, and if the roof is steep or the chimney is more than two stories up, hire a professional instead of climbing it yourself.
Measure First: The Step That Decides Everything
Most chimney cap failures start with bad measurements. A cap that is even half an inch too small will not slide over the flue, and a cap that is too large will rattle and work loose. Take two sets of measurements.
For a single flue cap that slides over the flue tile: measure the outside width and length of the flue tile at the top. Add about 1/2 inch on each side for clearance and order a cap that size or slightly larger. The five most common square and rectangular flue sizes are 9 by 9, 9 by 13, 9 by 18, 13 by 13, and 13 by 18 inches. Round flues most commonly run 6, 8, 10, 12, or 14 inches in diameter.
For a crown mount cap that covers the whole crown: measure the full crown from outside edge to outside edge, width and length. Also measure the height from the crown surface to the top of the tallest flue tile. The cap mesh must be at least 5 inches taller than the tallest flue on the sides, and the lid must sit at least 4 inches above the flue tile, so smoke has room to escape and the draft is not choked.
| Flue Shape | Common Sizes | Cap Type That Fits |
|---|---|---|
| Square or rectangular clay tile | 9 by 9, 9 by 13, 9 by 18, 13 by 13, 13 by 18 inches | Bolt on, multi fit, adjustable, universal |
| Round metal or clay flue | 6, 8, 10, 12, 14 inches diameter | Bolt on round, slip in |
| Flush flue, no protrusion | Crown dimensions vary | Crown mount top mount cap |
| Two or more flues | Crown dimensions vary | Multi flue crown mount cap |
Write the numbers down on paper before you climb down. Do not trust memory for a measurement you will order from.
The 7 Chimney Cap Styles and How Each One Attaches
Every cap on the market uses one of seven attachment styles. Knowing which style you own tells you exactly how it fastens, what tools it needs, and whether you can remove it later for cleaning.
1. Bolt On Single Flue Cap
The most common stock cap. It slides over a single protruding flue tile and fastens with four bolts, one at each corner of its base. Slide it on, center it so the overhang is equal on all sides, then hand tighten all four bolts evenly before snugging them with a nut driver. The bolts press against the outside of the flue tile and hold the cap by friction. They must not penetrate the tile. Some caps include a protective metal strip between the bolt and the tile so the bolt cannot crack it. Never overtighten on an older clay tile, which can crack under pressure. A bolt on cap comes off easily for chimney cleaning, which is a real advantage.
2. Multi Flue Crown Mount Cap
For chimneys with two or more flues, one large cap covers the whole crown. It does not attach to the flues at all. It attaches to the concrete crown through four flanges, one on each side of the cap, with holes for masonry screws. Set the cap on the crown, keep every flange at least 1 inch from the edge of the crown so drilling does not split the concrete, trace the flange positions, lift the cap off, and drill pilot holes with a hammer drill and a 3/16 inch bit to a depth of about 1 1/2 inches. Run a bead of construction adhesive just inside the traced line, set the cap back in exactly the same spot, press it down to seat the adhesive, and drive the masonry screws through the flange holes. Finish by sealing the flange perimeter with elastomeric sealant.
3. Band Around Brick Cap
This cap grips the top layer of chimney brick instead of the flue or the crown. A metal band at the bottom of the cap slides over the top course of brick, and adjustable corner pieces with nuts and bolts tighten the band around the brickwork. It comes in four sizes, each with about 2 inches of adjustability, and it needs no drilling into the crown or the brick. That makes it a good choice when the crown is cracked or too thin to anchor into. Tighten the four corners evenly until the cap is snug and does not shift when you tug it.
4. Multi Fit Cap
A flexible single flue cap made for square, rectangular, and round flues. It comes in small, medium, and large, and each size covers a range of flue dimensions. Installation starts by attaching four braces to the top cover of the cap, leaving the bolts loose. The other ends of the braces clamp down onto the flue tile as you tighten the bolts. Once the cap is secure on the flue, tighten the bolts on the top cover to finish. The adjustability is useful when your flue falls between standard sizes.
5. Adjustable Bolt On Cap
Similar to the multi fit, but held together by four L shaped braces with slots that accept U shaped brackets. Slide the brackets along the slots to match your flue size, slip the brackets onto the flue tile, and tighten the bolts. It comes in small and large only, and fits a narrower range of flue sizes than the multi fit, but it is simpler to install.
6. Slip In Cap
The easiest cap to install, and the only one that needs no hardware at all. It is made for round flues and comes in diameter ranges such as 9 1/2 to 10 1/2 inches. You simply slip it into the flue tile. The angle of its legs, plus the tension from their tendency to spring back, holds it firmly in place. Check that it sits level and cannot be lifted out by hand before you climb down.
7. Universal Cap
A single flue cap with an inside anchoring system. Its mesh tucks in at a right angle toward the flue. To install it, unscrew the wing nuts at the top and remove the cover, set the cap on the flue so the mesh hangs over the edge, and slide a V shaped anchor bar down into the chimney so both ends touch the flue walls. Lay the straight metal bar across the mesh, pass the top of the anchor bar through one of the three holes in the straight bar, and thread the wing nut on. Tightening the wing nut creates tension between the anchor, the bar, and the cap mesh. Reattach the cover and the installation is done.
| Cap Style | Attaches To | Tools Needed | Removable for Cleaning |
|---|---|---|---|
| Bolt on single flue | Flue tile, set screws | Nut driver | Yes, loosen 4 bolts |
| Multi flue crown mount | Concrete crown, masonry anchors | Hammer drill, impact driver | Yes, remove screws |
| Band around brick | Top course of brick, tension | Wrench | Yes, loosen corner bolts |
| Multi fit | Flue tile, clamp braces | Wrench | Yes |
| Adjustable bolt on | Flue tile, U brackets | Wrench | Yes |
| Slip in | Inside of round flue, tension | None | Yes, pull straight out |
| Universal | Inside of flue, anchor bar | None, wing nuts by hand | Yes |
Choosing the Cap Material and Mesh
The material decides how long the cap lasts, and the price gap between materials is small compared with the cost of replacing a cap every few years.
304 stainless steel is the best long term choice. It does not rust, it handles high temperatures from wood burning fireplaces, and it lasts 20 to 30 years or more. A standard stainless single flue cap costs $60 to $150.
Galvanized steel is the budget option at $30 to $80. It works in most climates but will rust at welds and edges after 5 to 10 years, faster in humid or coastal areas. Painted galvanized lasts a little longer, 7 to 15 years.
Copper is the premium choice. It lasts indefinitely and develops an attractive patina, but it costs several hundred dollars and is usually chosen for appearance on high end homes.
Aluminum is light and cheap, but it softens at high temperatures. It is acceptable for gas fireplaces, which produce no sparks and less heat, and not recommended for wood burning fireplaces.
On mesh, remember the code rule from earlier in this guide: the screen must stop a 1/2 inch sphere and pass a 3/8 inch sphere, with net free area at least four times the flue outlet area. The standard 3/4 inch mesh on most stock caps meets this for typical flues. Smaller mesh clogs with creosote faster and chokes the draft. Larger mesh lets embers through. If your local code requires 5/8 inch mesh, buy a cap made for that rule rather than modifying a stock cap.
Step by Step: Prepare the Chimney and Remove the Old Cap
Before the new cap goes on, the old one has to come off and the seating surface has to be clean.
First, inspect the existing cap and the crown from the roof. Photograph the installation from several angles so you can refer to the photos when positioning the new cap. Check the old cap for rust holes in the mesh, bent mesh that suggests an animal forced entry, and cracked or loose mortar at the base. Check the crown for cracks, because a cracked crown lets water into the chimney structure and should be sealed with crown repair sealant before or at the same time as the cap replacement. Shine a flashlight down the flue and look for nesting material. Never seal a nest inside a flue.
Remove the old cap according to its style. A clamp style cap comes off by loosening the four set screws with a nut driver, then lifting straight up. If rust has seized it, work a flat pry bar gently under the base, but never lever against the flue tile. A mortar set cap needs a cold chisel and hammer to break the mortar joint around the base. Work around the perimeter, not in one spot, to avoid cracking the crown. A crown mount cap comes off by reversing the masonry anchors with a drill, then scoring around the flange with a utility knife if it is bedded in sealant.
Once the old cap is off, clean the top of the flue tile and the crown with a wire brush and scraper. Remove all loose mortar, soot, and debris. A clean surface is what makes the new seal hold. If the flue tile edge is chipped, fill small chips with hydraulic cement or refractory mortar and let it set before installing the new cap. If the flue tile is cracked through or spalling, stop and have a chimney professional evaluate it. A cracked flue tile is a fire and carbon monoxide hazard, not a do it yourself repair.
Method A: Clamp and Bolt On Attachment for a Single Flue
This is the method most homeowners use, and it takes about 20 minutes once the measurements are right. Dry fit the cap first: slide it over the flue tile, check that it sits level with equal overhang on all sides, then lift it off again. Slide it back down until it is fully seated on top of the flue tile. Hand tighten all four set screws evenly, one at a time, going around the cap in order. Do not tighten one fully before starting the others, or the cap will sit crooked. Go back around with a nut driver and snug each bolt. Snug means firm resistance, not maximum force. On older clay tiles, overtightening is the most common way a do it yourself installation ends in a cracked flue. Tug the cap gently from several angles. It should not shift, rock, or lift. If it moves, loosen the bolts, recenter the cap, and tighten again.
This method needs no drilling into masonry, and the cap comes off in minutes for annual chimney cleaning. That is why it is the standard choice for a single flue chimney with a protruding tile.
Method B: Masonry Anchor Attachment for a Crown Mount Cap
Use this method for multi flue chimneys and for single flue chimneys where the flue sits flush with the crown. Set the cap on the crown and center it over the flues, keeping every flange at least 1 inch from the edge of the crown. Mark the anchor hole positions through the flange holes and trace a line around each flange. Lift the cap off, drill pilot holes at the marks with a hammer drill and a 3/16 inch masonry bit, about 1 1/2 inches deep, and brush away the dust. Run a bead of construction adhesive or high temperature sealant just inside the traced flange lines. Set the cap back in exactly the same spot along the traced lines and press down firmly to seat it on the adhesive. Drive the masonry screws or hammer anchors through the flange holes into the pilot holes with an impact driver. A 3/16 inch bit with a 1/4 inch Tapcon style screw is the usual pairing. Finish with a continuous bead of elastomeric chimney sealant around the full perimeter of each flange where it meets the crown, smoothed with a wet finger. This bead is the primary weather seal, so leave no gaps. Let the adhesive and sealant cure per the product label before the next heavy rain if you can.
Method C: Mortar Set Attachment
The traditional method, still used for heavy caps and for caps on older masonry chimneys where anchors will not hold. Mix a small batch of type S mortar to a stiff consistency, the kind that holds its shape on a trowel. Apply a 3/4 inch bed of mortar to the crown around the flue tile. Set the cap into the mortar bed, press down firmly, and check for level in both directions. Pack mortar around the full perimeter of the cap base, sloping it away from the cap so water sheds off instead of pooling against the joint. Smooth the mortar joint with a trowel and let it cure 24 to 48 hours before heavy rain or freezing temperatures.
Mortar set caps are the hardest to remove later, because the joint has to be chiseled out. They are also the most forgiving of an uneven crown, since the mortar bed fills small gaps. Do not use this method on a crown that is already cracked or crumbling. The mortar will not bond to loose concrete, and the cap will work loose with the first freeze.
Method D: No Drill Tension Caps
Three cap styles attach without drilling, mortar, or screws, and they are worth knowing about when the crown or flue cannot take fasteners. Band around brick caps tighten around the top course of brick with corner nuts and bolts. They are the best no drill option for a masonry chimney with a damaged crown, because they never touch the crown at all. Slip in caps drop into a round flue and hold by spring tension. They suit metal flues and round clay flues where the diameter matches one of the stock ranges. Confirm the fit by hand before you leave the roof. If you can lift it out with one hand, it is the wrong size. Universal caps anchor inside the flue with a V shaped bar and a wing nut. They work on square and rectangular flues where a bolt on cap will not fit, for example when the flue tile is too short to grip from the outside. The anchor bar must touch both flue walls, or the tension will not hold.
No drill methods are genuinely secure when the cap is sized right, and they are the easiest to remove for cleaning. Their weakness is sizing. A tension cap that is slightly too large or slightly too small will not hold, and there is no screw to compensate for a bad fit.
How to Attach a Chimney Cap Without Mortar
Most caps sold today attach without mortar, and mortar is no longer the default. If you want to avoid mortar entirely, choose a bolt on single flue cap that clamps to the flue tile, a crown mount cap fastened with masonry anchors and sealant, or a tension cap such as band around brick or slip in. All three hold securely without a mortar bed, and all three come off for cleaning without a chisel. Mortar is still the right choice in two situations: a heavy custom cap that needs the weight of a mortar bed to stay put, and a crown so uneven that no flange sits flat on it. In every other case, a mechanical attachment plus sealant is faster, cleaner, and easier to reverse.
Sealing and Weatherproofing the Cap
Attachment holds the cap in place. Sealing keeps water out of the joint, and the joint is where most cap failures actually start. Apply a continuous bead of high temperature silicone sealant or elastomeric chimney sealant around the full perimeter of the cap base where it meets the flue or the crown. Do not leave gaps at the corners, and do not rely on the mechanical fasteners alone to keep water out. Water that gets under the base runs down the outside of the flue and into the chimney structure, where it rots the damper, stains the firebox, and soaks the masonry from the inside.
On a crown mount cap, seal the flange perimeter as the last step, after the anchors are driven. On a clamp cap, seal the small gap between the cap base and the flue tile if one is visible. Use sealant rated for the temperatures at the top of a chimney, not ordinary household caulk, which will crack and peel within a season. Check the sealant every year when you inspect the cap, and reapply it when it shows cracks or pulls away from the metal.
Inspect and Test the Installed Cap
A cap that looks right can still be wrong. Run these checks before you climb down. The cap sits level and centered, with equal overhang on all sides. The mesh is fully intact, with no openings larger than the mesh size and no bent sections. The cap clears the flue tile by at least 4 inches on top and 5 inches on the sides. Every sealant joint is continuous, with no gaps or thin spots. Every bolt, anchor, or tension fitting is snug, and the cap does not shift when you tug it. The crown around the cap shows no new cracks from drilling or tightening.
If you have a wood burning fireplace, light a small test fire and watch the smoke. It should rise cleanly through the cap without spilling back into the room. If the draft is noticeably worse than before the cap went on, the cap may be undersized or the mesh may be too fine for your flue. Check the cap manufacturer specifications for your flue size before you assume the chimney is at fault.
What a Loose Cap Does to Your Roof
Here is the part most chimney cap guides skip: a failed cap is a roofing problem, not just a chimney problem. Rain that enters an uncapped flue runs down the inside of the chimney and soaks the masonry, but it also finds its way to the roof deck around the chimney base. That is the same area protected by the drip edge on the roof and the flashing that seals the chimney to the roof surface, and it is one of the most common leak points on any roof.
Water at the chimney base rots the deck sheathing, stains ceilings in the rooms below, and feeds mold in the attic. On a metal roof the stakes are higher still, because the flashing details around a chimney on metal are more complex and a leak there is harder to trace. The National Roofing Contractors Association publishes flashing details for chimneys that show how the cap, the flashing, and the roof covering are meant to work as one system. Our guide to the parts of a metal roof shows where the chimney flashing sits in the whole system. If your ceiling already shows stains near the chimney, the cap is only half the fix. The flashing and the seal at the chimney base need checking too, and that is a job for our roof repair service, which can trace a chimney leak to its source and tell you whether the cap, the flashing, or both are at fault.
A cap that blows off in a storm can also damage the roof directly. A sheet metal cap tumbling across shingles can tear the covering and dent metal panels, and it can end up in a gutter or on a neighbor property. A cap that is properly attached is not just protecting the chimney. It is protecting the roof around it.
Chimney Cap Cost in 2026
Cap prices depend on material and size, and the professional installation charge depends on roof access and chimney height.
| Item | Typical Cost |
|---|---|
| Galvanized steel single flue cap | $30 to $80 |
| Stainless steel single flue cap | $60 to $150 |
| Copper single flue cap | Several hundred dollars |
| Multi flue or custom crown mount cap | $150 to $500 or more |
| Professional supply and install, standard cap | $100 to $250 |
| Full replacement including labor, most homes | About $300 |
| Full replacement, large or custom cap | $125 to $1,000 |
A do it yourself installation costs only the cap and a tube of sealant, usually $100 to $200 in materials for a standard stainless cap. The saving is real, but only if you are comfortable working on a roof. A chimney sweep or roofer who is already on site for an annual cleaning will often supply and install a standard cap for $100 to $250 total, and that price includes the warranty on the work. If the chimney is tall, the roof is steep, or the crown needs repair before a cap will seal, the professional price is money well spent. For the full cost picture on the roof around the chimney, see our guide to average roof replacement cost.
When to Call a Professional
Most single flue caps are a reasonable do it yourself job for a homeowner who is comfortable on a roof. Call a professional when any of these apply: the chimney is more than two stories tall, or the roof is too steep to work on safely; the crown is cracked, crumbling, or missing chunks, and needs repair or a rebuild before any cap will seal; the flue tile is cracked, spalled, or missing, since a damaged flue is a fire and carbon monoxide hazard; animals are nesting inside the flue, and the nest must be removed and the flue inspected before you seal it with a cap; the chimney has multiple flues and needs a custom sized crown mount cap; or you are not comfortable working at height. A fall from a roof can cause serious injury, and no cap is worth that risk.
A chimney sweep or roofer can also spot problems you would miss, such as a deteriorated crown, a flue liner that has shifted, or flashing that has pulled away from the brick. Look for a sweep certified by the Chimney Safety Institute of America, which sets the standard for chimney inspection and cleaning. If you are planning a full roof replacement, have the chimney cap and flashing handled in the same job. Our residential roofing service covers the cap, the flashing, and the roof as one system, so nothing gets missed between trades. On a metal roof, the same applies: our metal roofing service includes the chimney flashing details that a cap alone cannot fix.
Maintenance and How Long a Cap Lasts
A chimney cap needs little maintenance, but it does need an annual look. Inspect it at the start of every heating season, ideally from the ground with binoculars first, then up close if anything looks wrong.
| Material | Expected Life |
|---|---|
| Galvanized steel | 5 to 10 years |
| Painted galvanized steel | 7 to 15 years |
| 304 stainless steel | 20 to 30 years or more |
| Copper | Indefinite |
| Aluminum, gas only | 10 to 20 years |
During the inspection, check the mesh for holes that would let animals in, check the sealant for cracks, and check that the cap is still tight. Surface rust on a galvanized cap can be treated with a wire brush, a rust converter, and high temperature paint if the metal is not perforated. If the mesh has rusted through, replace the whole cap. Spark arrestor integrity is a fire safety issue, and a patched mesh is not a reliable fix. Clean creosote off the mesh at least once a year. A mesh clogged with creosote restricts the draft and can push smoke back into the house. A cap that is easy to remove, such as a bolt on or slip in style, makes this a five minute job instead of a chore you put off.
Frequently Asked Questions
How do you attach a chimney cap? It depends on the cap style. A single flue cap slides over the flue tile and fastens with four set screws. A multi flue cap fastens to the concrete crown with masonry anchors. A traditional cap sets into a bed of type S mortar. Tension caps such as band around brick and slip in hold by friction and need no fasteners at all.
Can you attach a chimney cap without mortar? Yes. Most caps sold today attach without mortar. Bolt on caps clamp to the flue tile, crown mount caps fasten with masonry anchors and sealant, and tension caps hold by friction. Mortar is only needed for heavy custom caps or very uneven crowns.
What size chimney cap do I need? For a single flue cap, measure the outside width and length of the flue tile and add about 1/2 inch on each side. For a crown mount cap, measure the full crown from edge to edge, plus the height from the crown to the top of the tallest flue tile. The cap mesh must clear the tallest flue by at least 5 inches on the sides.
How much does it cost to install a chimney cap? The cap itself costs $30 to $80 in galvanized steel or $60 to $150 in stainless steel. Professional supply and install of a standard cap runs $100 to $250, and a full replacement including labor is about $300 for most homes. Large or custom caps can run $125 to $1,000 installed.
Do I need a chimney cap if I have a gas fireplace? A rain cap is still worth having, because it keeps water and animals out of the flue. A spark arrestor mesh is not needed for gas, since gas produces no sparks, and some gas caps use open sides without mesh to reduce flow restriction. Never use an aluminum cap on a wood burning fireplace.
What mesh size should a chimney cap have? The International Residential Code requires a spark arrestor screen that stops a 1/2 inch sphere and passes a 3/8 inch sphere, with net free area at least four times the flue outlet area. Most stock caps use 3/4 inch mesh, which suits most homes. In wildfire prone areas, local codes may require tighter mesh, so check before you buy.
Can I install a chimney cap myself? Most homeowners can install a single flue bolt on cap themselves if they are comfortable working on a roof. You need a tape measure, a nut driver, a wire brush, and a caulk gun. Hire a professional if the chimney is tall, the roof is steep, the crown is damaged, or the flue tile is cracked.
How long does a chimney cap last? Galvanized steel lasts 5 to 10 years, painted galvanized 7 to 15 years, 304 stainless steel 20 to 30 years or more, and copper indefinitely. Inspect the cap every year at the start of the heating season and replace it when the mesh rusts through or the metal is perforated.
Planning roof work around your chimney? Start with our guide to roof underlayment, check the edge detail in what is a drip edge on roof, or see the full system in parts of a metal roof. For a free inspection and an itemized quote on a cap, flashing, or a full roof, contact our team.

