Roofing Material Calculator

One form, the whole order: field bundles, ridge cap, starter strip, underlayment rolls, decking sheets, drip edge and nails, each figured from the published rate for that item. Free, no signup, no waiting.

Contractors call this a takeoff: the complete count of everything a roof consumes, built line by line before anyone climbs a ladder. Homeowners and DIY roofers search for it because ordering short stops a job cold, and ordering blind wastes hundreds. This calculator runs the same takeoff a supplier counter would, with every rate shown.

The calculator

Please enter your roof area in square feet (a number greater than zero).

1. Roof size and shape

True sloped area in square feet. Shape sets the waste allowance: 10 percent for a gable roof, 15 percent for a hip roof, the standard estimator defaults.

2. Edge lengths

Ridge drives cap bundles. Eaves plus rakes drive starter strip and drip edge. Leave a field at zero if you do not know it yet.

Your materials list

Every rate on this list is a manufacturer spec or a standard estimator figure, detailed in the notes under the calculator.

The rate behind every line

  • Field bundles: 3 bundles per square for architectural shingles, per GAF and Owens Corning packaging, with 10 percent waste on a gable roof or 15 percent on a hip roof.
  • Ridge cap: 25 linear feet per bundle, the planning figure takeoff guides use inside the published 20 to 35 foot product range.
  • Starter strip: 100 linear feet per bundle, run along every eave and rake.
  • Underlayment: synthetic rolls cover 10 squares, 15 lb felt covers 4 squares, 30 lb felt covers 2 squares, all manufacturer roll specs. The standalone roof underlayment calculator goes deeper on layers and low slope rules.
  • Decking sheets: a 4 by 8 sheet covers 32 square feet. The count shown assumes a full re deck; the roof decking calculator handles partial replacement.
  • Drip edge: sold in 10 foot pieces, each covering 9.83 feet after the standard 2 inch lap.
  • Nails: 320 per square at the standard four nail pattern on architectural shingles. Coil nails run 120 to a coil and 7,200 to a box.

Sample takeoff for a 20 square gable roof

Item Rate Count for 2,000 sq ft
Field bundles 3 per square plus 10 percent waste 66 bundles
Ridge cap bundles 25 LF per bundle, 40 LF ridge 2 bundles
Starter bundles 100 LF per bundle, 140 LF of edge 2 bundles
Synthetic underlayment 10 squares per roll 3 rolls
Decking sheets 32 sq ft per sheet, if fully re decked 69 sheets
Drip edge 10 ft pieces at 9.83 ft effective 15 pieces
Coil nails 320 per square about 7,040 nails

Rates cross checked against manufacturer documentation from GAF and the estimating guidance published by the NRCA. If you only need the shingle count, the focused shingle bundle calculator is faster.

What a takeoff cannot see

  • Ice and water shield. Cold climates protect every eave with membrane running two feet past the inside wall line, plus every valley. That count depends on your eave length and climate zone, so it is figured on the job, not from area alone.
  • Flashing metal. Chimneys, skylights and wall junctions each take their own flashing kit. A takeoff from area alone cannot count your penetrations.
  • Ventilation hardware. Ridge vent runs the length of the ridge, and box vents or turbines follow the attic math in our attic ventilation calculator.
  • Deck surprises. The sheet count here is the ceiling, not the expectation. Most re roofs find sound decking and replace a handful of sheets; the full count exists so the budget survives the worst case.

When the list looks right, the roof cost calculator prices the same roof fully installed.

Frequently asked questions

What materials do I need for a new shingle roof?

Field shingles, ridge cap shingles, starter strip, underlayment, ice and water shield at eaves and valleys, drip edge, roofing nails, pipe boots and flashing for every penetration, plus ridge vent or other ventilation. This calculator counts the area driven items; flashing and vents follow your roof layout.

How many nails does a roof take?

About 320 per square at the standard four nail pattern, so a 22 square roof needs roughly 7,000 nails, which is one standard 7,200 count box of coil nails. High wind installations use six nails per shingle and need about 480 per square.

Why does the calculator show decking for a re roof?

As a worst case planning number. Tear off sometimes reveals rotted decking that must be replaced before new shingles go down, and contractors price that per sheet. Knowing the full count in advance stops a mid job surprise from becoming a dispute.

How accurate is this materials list?

The rates are manufacturer specs and standard estimator figures, so counts land where a supplier takeoff lands for the same inputs. The inputs are the risk: a wrong roof area or a missed rake length moves every line. Measure edges with a tape where you can, from the ground or a ladder at the eave, never by walking a roof you are not equipped for.

List in hand? Let a roofer sanity check it free.

A free inspection verifies the area, the edges and the deck before the order goes in.