Roof Pitch Finder

Enter your roof’s rise and run and get the pitch, the angle in degrees, the category, the true area multiplier, and what the slope does to your labor cost. Free, no signup, no waiting.

The finder

Please enter a rise of 0 or more and a run greater than zero, in inches.

1. Rise and run

Measure the vertical rise over a horizontal run, in inches. The classic way: hold a 12 inch level against a rafter inside your attic and measure straight up from the 12 inch mark.
Almost always 12 — roof pitch is quoted as rise over a 12 inch run.

2. Home footprint (optional)

Add your home's ground floor square footage and the finder converts your pitch into true roof surface area and roofing squares.

Your roof pitch

Planning figures from 2026 contractor-reported cost data. Real quotes vary by market, roof complexity and contractor. This is a guide, not a bid.

How the math works

Roof pitch is always quoted as rise over a 12 inch run, written like 6/12. Three exact calculations turn your two measurements into everything a roofer needs:

  1. Pitch. Your rise is normalized to a 12 inch run: rise times 12 divided by run. Measure 8 inches of rise over a 10 inch run and your pitch is 9.6/12.
  2. Angle. The arctangent of rise over run, converted to degrees. A 6/12 pitch is 26.6 degrees, a 12/12 pitch is exactly 45 degrees.
  3. Area multiplier. The secant of the angle, or the rafter length over a 12 inch run: the square root of (144 plus rise squared), divided by 12. Multiply your home’s footprint by this number and you get the true sloped surface area. A 6/12 roof has a multiplier of 1.118, so a 2,000 square foot footprint is really 2,236 square feet of roof.

The labor cost effect comes from 2026 contractor reported data, not from the geometry. Steep roofs slow crews down, demand harnesses and staging, and OSHA requires fall protection at 7/12 and steeper. That safety overhead lands in your quote.

Common roof pitches, angles and cost effects (2026)

Angles and area multipliers are exact geometry. Categories follow the standard industry pitch chart. Labor effects are 2026 ranges from contractor reported pricing.

Pitch Angle Area multiplier Category Labor cost effect
2/12 9.5° ×1.014 Low slope None
3/12 14.0° ×1.031 Low slope None
4/12 18.4° ×1.054 Conventional None
5/12 22.6° ×1.083 Conventional None
6/12 26.6° ×1.118 Conventional ×1.10 to ×1.20
7/12 30.3° ×1.158 Conventional ×1.10 to ×1.20
8/12 33.7° ×1.202 Steep ×1.15 to ×1.25
9/12 36.9° ×1.250 Steep ×1.15 to ×1.25
10/12 39.8° ×1.302 Steep ×1.20 to ×1.30
11/12 42.5° ×1.357 Steep ×1.20 to ×1.30
12/12 45.0° ×1.414 Steep ×1.20 to ×1.30

6/12 is the most common residential pitch in the US. For what a full replacement costs once you know your numbers, see our average roof replacement cost guide and run your figures through our roof cost calculator.

Why pitch changes your roofing quote

  • Fall protection. OSHA classifies 7/12 and steeper as steep slope work, so crews must rope in. Harnesses, anchors and staging add setup time to every day of the job.
  • Crew speed. Roofers move slower and carry less on a steep slope. Contractor data puts steep pitch labor 20 to 40 percent above low slope labor for the same square footage.
  • Material handling. Bundles cannot sit on a steep slope, so material goes up by conveyor or gets staged and hand carried, both slower than on a walkable roof.
  • Waste factor. Steeper cuts around valleys and hips waste more material. Estimators raise the waste allowance on steep roofs, which shows up in the material line.
  • The 8/12 jump. Contractors report $1,000 to $3,000 in extra labor once a roof hits 8/12, purely for safety equipment and reduced crew speed.
  • Labor is not the whole bill. Labor runs roughly 40 to 50 percent of a full replacement, so a 25 percent labor adder moves the total project about 10 to 15 percent. A steep roof adds 10 to 20 percent to the total versus a standard slope.

How accurate is this finder?

The geometry is exact: pitch, angle and area multiplier are pure math, accurate to the measurements you enter. Measure carefully in the attic with a level and a tape and the numbers are as good as a contractor’s.

The labor cost effect is a planning range, not a quote. It reflects 2026 national contractor reported data, but your market sets the real number: high wage metros run above the range, simple gable roofs run below it, and roof complexity (valleys, dormers, stories) moves labor independently of pitch. Use it to sanity check bids: if two quotes differ mainly because one crew priced your 10/12 honestly and the other priced it like a 5/12, the cheaper bid is the one to question.

Frequently asked questions

What is roof pitch?

The steepness of a roof, expressed as the inches of vertical rise over a 12 inch horizontal run. A 6/12 pitch rises 6 inches for every 12 inches of horizontal distance, which is an angle of 26.6 degrees.

How do I measure my roof pitch without climbing on the roof?

Go into the attic, find a rafter, and hold a 12 inch level horizontally against its underside. Measure straight up from the 12 inch mark to the rafter. That measurement in inches is your rise, and your pitch is that number over 12. Never climb onto a roof to measure unless you are a professional with safety gear.

What is the most common roof pitch in the US?

6/12. It sits in the middle of the conventional range: steep enough to shed water and snow well, shallow enough for crews to walk, and compatible with every common roofing material.

What pitch is considered a steep roof?

8/12 and above is the industry’s steep category. The regulatory line sits lower: OSHA requires fall protection at 7/12 and steeper, which is one reason quotes step up there.

How much does roof pitch add to replacement cost?

Expect 10 to 20 percent on the total project for a steep roof versus a standard slope, driven by 20 to 40 percent higher labor. At 8/12 and above, contractors report $1,000 to $3,000 in extra labor alone for safety equipment and slower crew speed.

What is the roof pitch multiplier used for?

Converting a home’s footprint into true roof surface area. Multiply the ground floor square footage by the multiplier (1.118 for a 6/12, 1.414 for a 12/12) to get the sloped area roofers actually cover, then divide by 100 for roofing squares when ordering material.

What is the minimum pitch for asphalt shingles?

Most shingle manufacturers require 4/12 for a standard installation. Between 2/12 and 4/12, shingles need a special low-slope application with doubled underlayment, and below 2/12 you need a membrane roof instead. If your pitch came out low, our shingle roofing page covers which systems fit which slope.

Does a steeper roof last longer?

Often yes for the roof covering itself: steep slopes shed water and snow faster, so shingles spend less time wet. The tradeoff is cost. Steeper roofs are more expensive to install, inspect and repair, so lifetime value depends on your climate and how long you plan to stay.

Know your pitch? Get your number.

The finder gets you the geometry. A free inspection turns it into a real quote.