Drip edge metal is the thin bent strip of metal that runs along the edges of a roof and throws water clear of the fascia, the deck, and the walls below. It is one of the cheapest parts of a roof, and one of the most consequential. A full perimeter of drip edge metal on a typical home costs $150 to $1,000 installed, while the fascia rot and deck damage it prevents can cost $600 to $6,000 to repair.
The metal itself is the decision that matters most. Aluminum, galvanized steel, copper, and stainless steel all do the same job, but they differ wildly in price, lifespan, and what roof they belong on. Pick the wrong metal and you get rust streaks, dented edges, or galvanic corrosion that eats the flashing from the inside. Pick the right one and the edge outlasts the roof covering it.
This guide covers every drip edge metal type and profile, what each metal costs per linear foot in 2026, the gauges and sizes the code actually requires, how to match the metal to your roof panels, and how the metal is installed on shingle roofs and on metal roofs.
What Is Drip Edge Metal
Drip edge metal is a length of bent sheet metal, usually sold in 10 foot pieces, that is fastened along the eaves and the rake edges of a roof. One leg lies flat on the roof deck and the other bends down over the fascia, with a small outward kick at the bottom that breaks the surface tension of water and makes it drop clear of the building instead of curling back under the edge.
Water does not always fall straight down. Surface tension can make a drop cling to the underside of a shingle and roll back toward the fascia, and wind can push rain sideways and up under the roof edge. Bare wood soaks that water up. The metal gives water a sharp lip to fall from, so it lands in the gutter or on the ground instead.
The eaves are the lower horizontal edges where gutters hang. The rakes are the sloped edges on the gable ends, which usually have no gutters. Drip edge metal belongs on both. At the eaves it goes on the deck first and the underlayment goes over it. At the rakes the underlayment goes on first and the metal goes over it. That layering order is the detail most often installed backwards, and getting it wrong channels water under the protection layers instead of over them. Our guide to what is a drip edge on a roof explains the full system, while this guide focuses on the metal itself: the profiles, the materials, the gauges, and the costs.
On a metal roof the same piece does extra work. The slick surface of metal panels sheds water faster than shingles, so the edge sees more water moving faster, and the perimeter is where wind uplift forces are highest. On standing seam systems the eave and rake trims are engineered as part of the wind uplift perimeter, and the drip edge metal locks the bottom of the panels down. A standing seam metal roof without proper edge metal is a roof that can peel from the edge in a storm.
Drip Edge Metal Profiles: Type C, Type D, and Type F
There are three standard profiles, and the profile decides how far water is thrown from the fascia.
Type C, the L Style
Type C is a simple 90 degree bend, shaped like the letter L. It is the most basic profile and usually the lowest cost. It works well on low slope roofs and on jobs where budget matters more than maximum water throw. Its weakness is that water can still cling to the short vertical leg and reach the fascia in wind driven rain.
Type D, the T Style
Type D is bent so the bottom kicks outward, shaped like a T, which is why roofers also call it D metal or T style. The longer outward kick throws water further from the fascia and directly into the gutter. The Asphalt Roofing Manufacturers Association recommends Type D for most residential roofs, and it is the profile most contractors install by default. If you are replacing drip edge metal and nobody specifies a profile, Type D is the safe choice.
Type F, the Gutter Apron
Type F is also L shaped, but with a longer leading edge that drapes further down over the fascia and reaches into the gutter. It is the profile used when runoff overshoots a standard drip edge, and it is the easiest profile to slide under existing shingles, so it is the common choice for retrofits and for rake edges. Roofers call it a gutter apron, and it is the profile to ask for when the gutters sit low or the roof has a long overhang.
| Profile | Shape | Best Use | Key Benefit |
|---|---|---|---|
| Type C | L shaped, 90 degree bend | Low slope roofs, tight budgets | Simple, lowest cost |
| Type D | T shaped, outward kick | Most residential roofs | Throws water furthest from fascia |
| Type F | Extended L shape | Roofs with gutters, retrofits | Reaches into the gutter, slides under existing shingles |
Drip Edge Metal Materials Compared
Four metals dominate the market. The right one depends on your roof material, your climate, and how long you expect the roof to last.
Aluminum Drip Edge
Aluminum is the most common drip edge metal in the United States, and the cheapest. It is light, it never rusts, it comes in many colors, and it is easy to bend on site. A color matched aluminum edge can disappear against the fascia and trim. Its weaknesses are that hail can dent it, it is softer than steel so it bends more easily under foot traffic or ladders, and it must never sit in contact with copper or copper runoff, which corrodes it. Aluminum is the right choice for most shingle roofs in mild climates, and for coastal homes where salt air would eat steel.
Galvanized Steel Drip Edge
Galvanized steel is stronger than aluminum and holds up better in high wind and hail. The zinc coating fights rust, but cut edges and scratches expose bare steel, so any cut needs care and the coating eventually wears thin in harsh climates. The code calls for steel of at least 24 gauge to hold up against strong winds and prevent rust. Steel is the right choice for high wind areas and for homeowners who want the toughest edge for the money. It is also the standard choice under a steel roof, where matching metals matters.
Copper Drip Edge
Copper is the premium drip edge metal. A 20 ounce copper edge is very sturdy, it develops a patina instead of rusting, and it can last 75 to 100 years, which is longer than most roofs it protects. Homeowners usually choose it for curb appeal on high end and historic homes, and it is the natural match for a copper metal roof or a standing seam copper roof. The drawbacks are price, copper costs several times what aluminum does, and the fact that copper runoff corrodes aluminum and galvanized steel below it, so copper edge metal must never drain onto other metals. The Copper Development Association publishes the standard weights: 16 oz copper weighs 1.00 lb per sq ft and 20 oz copper weighs 1.25 lb per sq ft, and 20 oz is the heavier, longer lasting choice for exposed edge work.
Stainless Steel Drip Edge
Stainless steel is the strongest and most corrosion resistant drip edge metal, with a lifespan of 70 years or more. It is the choice for extreme environments, commercial roofs, and coastal homes where even galvanized coatings fail. Its cost sits between galvanized steel and copper, and it is rarely needed on an ordinary home, but where the budget allows it is the fit and forget option.
| Material | Cost per Linear Foot | Lifespan | Best For |
|---|---|---|---|
| Aluminum | $0.30 to $3.00 | 20 to 50 years | Most homes, coastal areas, color matching |
| Galvanized steel | $0.50 to $2.00 | 30 to 50 years | High wind areas, hail zones, steel roofs |
| Copper | $3.50 to $15.00 | 75 to 100 years | Premium and historic homes, copper roofs |
| Stainless steel | $5.00 to $9.00 | 70 years or more | Extreme climates, commercial roofs |
Drip Edge Metal Sizes and Gauges
Drip edge metal is sold by profile, by metal, and by thickness, and thickness is where most buying mistakes happen. Thin metal dents, oil cans, and lifts in wind. The code sets minimums, and they are worth knowing before you buy.
Aluminum drip edge must be at least 0.019 inch thick under the building code. That is roughly the thickness of a heavy aluminum baking sheet, and it is the minimum, not the target. Thicker aluminum, around 0.024 inch, resists hail dents and ladder damage noticeably better and is worth the small price increase.
Galvanized steel drip edge should be at least 24 gauge. Thinner steel, 26 or 28 gauge, is cheaper and common at big box stores, but it bends easily, rusts sooner at cut edges, and can lift in high wind. In hurricane and high wind zones, 24 gauge is the floor and some contractors use 22 gauge on exposed edges.
The flange dimensions matter too. The leg that lies on the deck should extend at least 2 inches up the roof slope, and the vertical leg should extend at least 1/4 inch below the roof sheathing. Pieces come in 10 foot lengths and must overlap by at least 2 inches at every joint, with the overlap running downhill so water sheds over the seam instead of into it. Fasteners go every 12 to 18 inches along the flat leg, using corrosion resistant nails or screws that match the metal, so stainless fasteners with stainless edge metal and galvanized fasteners with galvanized steel.
One gap the competitor guides skip is gauge selection by climate. In hail country, go one gauge heavier than the minimum, because a dented edge holds water against the fascia. In coastal zones, choose aluminum or stainless over galvanized steel, because salt air attacks the zinc coating first. In high wind zones, choose hemmed edge profiles, where the bottom lip is folded back on itself, because the fold stiffens the metal and resists uplift far better than a flat cut edge.
How Much Does Drip Edge Metal Cost in 2026
Drip edge metal is a small line item on any roofing job, which is why it is so often left out of quotes, and why it is so cheap to add during a roof replacement and so expensive to add later.
Material only prices per linear foot, from national pricing guides:
| Material | Material Cost per Linear Foot |
|---|---|
| Aluminum | $0.30 to $3.00 |
| Galvanized steel | $0.50 to $2.00 |
| Copper | $3.50 to $15.00 |
| Stainless steel | $5.00 to $9.00 |
The wide aluminum range reflects the difference between plain mill finish stock at the low end and color matched, heavy gauge aluminum at the high end. Copper varies with the weight of the sheet and the copper commodities market, so get a current quote rather than budgeting from a national average.
Installed, a full perimeter job on a typical home runs $150 to $1,000, with the average near $575, or roughly $1 to $3 per linear foot including labor. For a typical United States home with about 200 linear feet of eave and rake, material alone runs about $200 for galvanized steel to about $3,000 for copper, and labor adds $1.50 to $3.00 per linear foot when a crew installs it.
What changes the price:
- Roof edge length. More perimeter means more metal and more labor, and complex rooflines with many gables cost more per foot than a simple rectangle.
- Material and finish. Color matched aluminum and copper cost far more than plain mill finish aluminum.
- New roof or retrofit. Adding drip edge metal to an existing roof costs more because the first courses of shingles must be lifted, while on a new roof the edges are already open and the crew is already on site.
- Roof height and pitch. Steeper or taller roofs need more safety gear and more time.
- Hidden damage. Rotted decking or fascia found under the old edge must be fixed first, and that repair is often the real cost of the job.
The cheapest time to add drip edge metal is during a full roof replacement, when it adds a few hundred dollars to a five figure job. The most expensive time is after the fascia has rotted, when the same edge metal comes with $600 to $6,000 of fascia and soffit repair. If your quote does not list drip edge metal as a line item, ask for it in writing before the crew starts.
Matching Drip Edge Metal to Your Roof
This is the section most guides mention in one sentence and then move on from, and it is the one that causes the most expensive failures. When two different metals touch each other in the presence of water, the less noble metal corrodes. Roofers call it galvanic corrosion, and on a roof edge it shows up as rust streaks, pinholes, and edge metal that crumbles years before its time.
The rule is simple: match the drip edge metal to the roof panels. Aluminum edge metal with aluminum panels. Galvanized steel edge metal with steel panels. Copper edge metal with copper panels. Stainless steel is compatible with most metals, but check the panel manufacturer guidance before mixing it with aluminum.
The expensive mistake is copper above other metals. Rain washing off a copper roof, a copper valley, or a copper chimney flashing carries dissolved copper onto whatever sits below it. If that is aluminum or galvanized steel drip edge metal, the copper plates onto the surface and corrodes it. On a copper roof, every edge metal, fastener, and gutter in the water path should be copper. On a steel roof, never use copper fasteners or copper edge metal.
Color matching is the other half of the decision. Drip edge metal is available in baked on paint and powder coat finishes in the standard colors of every major metal roofing system, so the edge can match the panels, the fascia, or the gutters. On a standing seam roof, order the edge metal from the same supplier as the panels so the color and the coating match exactly. A mismatched edge is visible from the street on every metal roof.
Drip Edge Metal on a Metal Roof
Drip edge metal behaves differently on a metal roof than on a shingle roof, and the competitor guides written for shingle roofs mostly skip the differences.
First, the profile. On standing seam roofs the eave detail is often a hemmed W style edge or an eave cleat, a folded metal piece that the bottom of the panel locks into. The cleat holds the panel down against wind uplift and gives the edge a clean finished look. A flat shingle style drip edge can work on a metal roof, but it does not lock the panel, and on exposed fastener roofs the panel screws should never be the only thing holding the edge down.
Second, the sequencing is stricter. The drip edge metal goes on the deck, the underlayment goes over it at the eaves, the panels go on, and the rake trim goes over the underlayment at the gables. At the rake the trim must overlap the panel edge and the underlayment, or wind driven rain will find the gap. Our guide to synthetic underlayment for metal roof covers the underlayment side of that sandwich.
Third, thermal movement matters. Metal panels expand and contract with temperature, and the edge metal must allow that movement. Panels attach with concealed clips that let them slide, and the drip edge metal must not pin the panel edge rigidly to the deck. That is one reason metal roof manufacturers specify their own edge details, and why following the panel manufacturer instructions matters more than following a generic flashing guide. GAF and the other major manufacturers all call for non corroding metal drip edge at eaves and rakes, and most metal roof system warranties require the specified edge metal to be installed correctly, or the weathertightness warranty does not apply.
Building Code Requirements for Drip Edge Metal
The International Residential Code, section R905.2.8.5, requires drip edge at the eaves and rake edges of asphalt shingle roofs, and most jurisdictions apply the same rule to metal roofs through the manufacturer installation instructions. The code requirements are specific:
- Adjacent pieces must overlap by at least 2 inches
- The vertical flange must extend at least 1/4 inch below the roof sheathing
- The metal must extend at least 2 inches up the roof deck
- The metal must be non corroding, which rules out plain uncoated steel
Local codes vary by city and county, so confirm the rules with your local building department before the job starts. A missing drip edge is one of the most common findings on re roof inspections, and it can hold up a home sale. Installation details can also affect your shingle warranty, so ask your roofer how they follow the manufacturer instructions, and get the answer in writing on the quote. The National Roofing Contractors Association is a good place to start when vetting any roofer credentials.
How Drip Edge Metal Is Installed
Understanding the steps helps you spot a bad installation before the shingles cover it up.
- Prepare the deck. Remove old material and debris, check for rot along the edge, and make sure the edge is straight. Rotten decking gets replaced before any metal goes on.
- Measure and cut. The metal comes in 10 foot pieces. Cut it to length with tin snips, and plan the joints so every overlap runs downhill.
- Start at the eaves. Lay the metal flush along the eave edge with the flat leg on the deck and the vertical leg over the fascia, so the bottom flange drops inside the gutter.
- Fasten it. Use corrosion resistant nails or screws every 12 to 18 inches along the flat leg. Never face nail through the vertical leg, where the hole would be exposed to weather.
- Overlap the pieces by at least 2 inches so water cannot pass through the seams. At corners, cut and bend a piece to fit snugly around the roof corner so the eave and rake pieces form a solid seal.
- Add underlayment. Lay it over the eave metal. Then set the rake metal over the underlayment.
- Install the roof covering. On shingle roofs, GAF guidance calls for a shingle overhang of about 3/8 to 3/4 inch past the metal. On metal roofs, set the panels into the eave cleat or over the drip edge per the panel manufacturer instructions.
Common installation mistakes to watch for: reversing the layer order at the eaves or rakes, short overlaps that leave seams open, too few nails, which lets wind lift the metal, a gap between the metal and the fascia where water can wick behind it, and a gutter set lower than the bottom edge of the metal, so water falls behind the gutter instead of into it.
Can drip edge metal be added to an existing roof? Yes, and Type F is the profile for it, because its long leading edge slides under existing shingles. The installer lifts the shingles along the edge, slides the metal underneath, and fastens it down. It is harder than adding it during a full replacement, it means working at the roof edge, which carries fall risk, and for most homeowners it is a job for a professional. If the roof is already leaking at the edge, our roof repair team can trace the source and fix the edge before the damage spreads.
Signs Your Drip Edge Metal Needs Replacing
Walk around your home and look up at the roof edge. Watch for these signs:
- Water stains or streaks behind the gutters, or water running down the siding after rain
- Fascia that is soft, peeling, dark, or moldy, which means water has been reaching the wood
- Metal that is bent, rusted, loose, or pulling away from the fascia, often after a hail storm or high wind
- Gaps between the roof edge and the fascia, where insects and small animals can enter
- Ceiling stains near exterior walls, which can mean water is entering at the edge and traveling inward
- No metal at the roof edge at all, common on homes built before the code required it
Any of these deserves a closer look. Catching edge damage early can keep a repair small, while ignoring it can mean replacing fascia, soffit, and decking. Hail can bend thin edge metal, so check it after every big storm, and check the rest of the roof at the same time. Our guide to steel roof maintenance covers the yearly roof edge routine in detail.
Drip Edge Metal Maintenance
Drip edge metal needs almost no maintenance, but the little it needs matters. Inspect it after major storms for missing or loose sections, clear debris that traps moisture against the metal, check lap joints and corners for gaps or corrosion, and repaint or reseal exposed cut edges as needed to prevent rust. On galvanized steel, touch up any scratch that exposes bare metal before rust starts. On copper, leave the patina alone, it is the protection. If a section is damaged, replace the full 10 foot piece rather than patching a short length, because a patch creates two new seams where water can enter.
Drip Edge Metal vs Gutter Apron
The two terms confuse homeowners because they describe overlapping parts. A gutter apron is Type F drip edge, the profile with the long leading edge that reaches into the gutter. All gutter aprons are drip edge metal, but not all drip edge metal is a gutter apron. The difference matters when runoff overshoots a standard edge: if water is falling behind your gutters, the fix is usually a Type F gutter apron, not a new gutter. If you are choosing between them on a new roof, Type D is the better all rounder, and Type F is the better choice where the gutters sit low or the roof has a long overhang.
Frequently Asked Questions
What is drip edge metal? Drip edge metal is a bent strip of sheet metal installed along the eaves and rake edges of a roof. It directs water away from the fascia and the roof deck and into the gutter, and it is required by the International Residential Code on shingle roofs.
What is the best metal for drip edge? Aluminum is the best choice for most homes because it never rusts, costs the least, and comes in many colors. Galvanized steel is better in high wind and hail. Copper is the longest lasting and the most expensive, and it belongs on copper roofs and premium homes. Always match the edge metal to the roof panels to avoid galvanic corrosion.
How much does drip edge metal cost? Material costs $0.30 to $15 per linear foot depending on the metal, with aluminum at the low end and copper at the high end. Installed, a full perimeter job on a typical home runs $150 to $1,000, with the average near $575, or about $1 to $3 per linear foot.
What gauge should drip edge metal be? Aluminum drip edge should be at least 0.019 inch thick, and galvanized steel should be at least 24 gauge. Thicker metal resists hail dents and wind lift better, so going one step heavier than the minimum is worth the small extra cost in storm prone areas.
Is drip edge metal required by code? Yes, in most of the United States. The International Residential Code, section R905.2.8.5, requires drip edge at the eaves and rake edges of asphalt shingle roofs, with at least 2 inches of overlap, at least 1/4 inch of extension below the sheathing, and at least 2 inches up the deck. Local codes vary, so confirm the rules with your local building department.
Can drip edge metal be installed on an existing roof? Yes. Type F drip edge, also called a gutter apron, is made for this, because its long leading edge slides under existing shingles. The installer lifts the first courses, slides the metal in, and fastens it down. It costs more than installing it during a roof replacement, and working at the roof edge carries fall risk, so most homeowners hire it out.
Does drip edge metal go under or over the underlayment? Both, depending on the edge. At the eaves the metal goes on the deck first and the underlayment goes over it. At the rakes the underlayment goes on first and the metal goes over it. Reversing that order is the most common installation mistake.
How long does drip edge metal last? Aluminum lasts 20 to 50 years, galvanized steel lasts 30 to 50 years, stainless steel lasts 70 years or more, and copper lasts 75 to 100 years. The edge usually outlasts the roof covering it, unless dissimilar metals or poor installation cause early corrosion.
Choosing a new roof? Compare systems in our guides to standing seam metal roofing and different types of metal roofing, check the pitch rules in minimum pitch for metal roof, and see how long each material lasts in how long does a metal roof last. For a quote on a metal roof with the right edge metal, see our metal roofing service.

